Manufacturing Rebounds in June, But Hiring Slows
Manufacturing activity grew in June, rebounding from an unexpected contraction the prior month, but hiring in the sector was the weakest in nearly four years, an industry report showed on Monday.
The Institute for Supply Management (ISM) said its index of national factory activity in June rose to 50.9 from 49.0 in May , a touch above of expectations of 50.5. A reading above 50 indicates expansion in the sector.
The gauge for new orders rose to 51.9 from 48.8 , while production jumped to 53.4 from 48.6 , helping the overall index bounce back from May's contraction - the first in six months.
But a measure of employment fell to 48.7, the lowest reading since September of 2009 . It stood at 50.1 in May.
That could feed concern about the strength of the U.S. recovery, particularly now that the Federal Reserve has said it is considering scaling back its massive stimulus program.
Economists polled by Reuters expect the broader U.S. economy to have slowed to 1.7 percent in the second quarter , though most say it should pick up steam in the second half.
The economy grew at a 1.8 percent rate in the first three months of the year, with consumer spending having grown less than initially thought.
http://www.nbcnews.com/business/manufacturing-rebounds-june-hiring-slows-survey-shows-6C10489618
Tags
Who is online
91 visitors

Another good, bad news and worse news report of economic data
I'm doing commodity manufacturing these days, so our planning is on a 12 month block. (if we're lucky)
From what I see in ours we are filling orders that will taper off come back to school, and we will see another spike for the holidays. After that, death valley till spring.
E I
I understand that business planning is done in a forward manner, the next quarter, the next year and the next five years and based on that planning the government sets expectations for metrics and when those metrics are missed or bettered it is reason to be sad or happy.
You are right that this does not fall into the "news flash" category it is merely a couple of more data points to be considered along with others when one makes an assessment of how the economy is doing.
As always thanks for the feedback
FLYNAVY1
Does your work force size fluctuate along with order volume?
E I
Agreed I like to look at the economic metrics on a monthly basis (or however often they are provided) as you say one or two periods of movement are not a trend to worry about, but once the trend gets much longer than three or four reporting periods it could become a trend and ears closer scrutiny.
Stagnation is a good explanatory term for much of what we see of late in the economy, good call
E I
Your questions was for FLYNAVY1 correct?
E I
I agree totally but we still need to stay abreast of the changing data points to stay currentin my view, even though knee jerk reactions to a single set of data points would be foolish
E I
Again I agree that they are individual and solitary data points and no decisions are conclusions should be reached based on a single set or single report
But we can look at them month after month and if a trend begins to form then react to it
Yes. We are nominally staffed at around 30/70, permanent/temp, and that provides us with a fast response to just in time manufacturing requirements. In some companies it was an even worse ratio and quality issues were directly proportional.
Seasonal makes us plan on a 12 month increment. Customer promotions can drive our planning down to as few as a 4-month planning cycle. As the business makes use of plastic, if enough of these promotions hit the market all at the same time, spot prices for material can drive the cost to manufacture up to the point of elimination of your profit margin.
I really hate the commodity market. I'll take automotive or biomedical manufacturing any day.
FLYNAVY1
Sounds like you have the right ratio for the fluctuating demand
EI is correct. Even in our volatile commodity market, if you sort out the noise of spot buys and lulls, the trend is that there is no trend in business outside of a flat line, and it has been that way for at least three years now.
I've not see real growth (5% or better) in the way of demand for molded product; precision, engineering grade, commodity or otherwise for about six years now. In commodity work we are trying to create our own demand by innovation of the product itself.
E I
I seeded an article, I did not write it and it provided the data points that the author put into his story
I enjoy the back and forth with you when you are debating a point and providing insight but sometimes you are simply belaboring a point and that is not so enjoyable
You should write an article about the long view of the trends on the data points presented so that everyone can see what they really mean when viewed over a period of time since that is in your view what is important,
flameaway
I am never sure if "prickly" refers to a thing with barbs or if it is the adjective to describe behavior of a prick
I always get it confused
We will be producing something for sale in Europe through a joint venture with the process having been created in the United States. Americans don't seem to be interested in the product, thus we are starting in Europe. Production has gone beyond the test market, and my job is to get it in to full scale production to penetrate as much of the European markets (East, West, North, South) as quickly as we can. Roll out to be first quarter of 2014. We won't have any real idea of how wide spread market acceptance will be till end of the third quarter next year. Big risk with lots of capital.
Of course if you listen to our sales people, they think we need to be producing wheel barrows to carry all the money we will be making. Me, I have my doubts. Executive boards don't listen to engineers like they do salesmen.
Well, Like I like to say about most sales department generated sales projections ....
.... even a broken clock is right twice a day.
flameaway
Indeed
(shrugs) then (grins) then (laughs out loud)
Thanks for a much needed laugh today